15&17, Ground Floor,
Jalan USJ 21/11,
UEP Subang Jaya,
47630 Subang Jaya,
Selangor, Malaysia.
+603-8081 7508
ESS (M) Sdn Bhd
15&17, Ground Floor,
Jalan USJ 21/11,
UEP Subang Jaya,
47630 Subang Jaya,
Selangor, Malaysia.
15&17, Ground Floor,
Jalan USJ 21/11,
UEP Subang Jaya,
47630 Subang Jaya,
Selangor, Malaysia.
MWH
Keep motors warm and moisture-free during extended shut-down periods.
AC Supply Voltage
200 to 600 Vac\
HP Ratings
3 to 900 HP
Easy to Install
Whether retrofitting an existing starter or installing a new one, the MWH Series is easy to apply. Just wire it in parallel to the magnetic starter’s line and load connection, connect the necessary auxiliary contacts and installation is complete.
Simple Adjustment
Output voltage is factory set to maintaina +5° to 10°C differential above ambient temperature. This adjustment can be used to trim the control as required for each application.
Self Protected
In addition to built-in fuse protection, the MWH Series features an RC snubber circuit across the SCR which protects it from any rapid rate of change in the system voltage. A metal oxide varistor (MOV) protects the unit against voltage spikes for reliable, maintenance-free operation.
Fully Automatic Operation
Designed for fully automatic operation, the MWH Series turns on when the motor starter has turned off. A built-in one minute timer ensures that the motor magnetic field has collapsed before it injects DC power into the windings. When the motor is restarted, the MWH Series instantly turns off. No operator interface is required... the MWH Series is in control.
Built-in Overload Sensing
The MWH Series had an optional shutdown input that can be connected to the N.O. auxiliary contact on the motor starter’s thermal overload relay. This will disable the motor winding heater control, preventing any additional heating in the motor and allowing for a faster motor cool down period. The MWH Series then goes back on-line after the overload relay is reset.
Ideal Alternative to Strip Heaters
Eliminate the cost and hassle of installing strip heaters into your motors. Simply wire up the MWH Series to generate heat throughout the motor stator windings. The heat is dissipated evenly without the “hot spots” caused by strip heaters. Conduction of heat to the rotor, bearings and shaft is also more effective which means maximized protection for the whole motor.
AC Supply Voltage
200 to 600 Vac\
HP Ratings
3 to 900 HP
Easy to Install
Whether retrofitting an existing starter or installing a new one, the MWH Series is easy to apply. Just wire it in parallel to the magnetic starter’s line and load connection, connect the necessary auxiliary contacts and installation is complete.
Simple Adjustment
Output voltage is factory set to maintaina +5° to 10°C differential above ambient temperature. This adjustment can be used to trim the control as required for each application.
Self Protected
In addition to built-in fuse protection, the MWH Series features an RC snubber circuit across the SCR which protects it from any rapid rate of change in the system voltage. A metal oxide varistor (MOV) protects the unit against voltage spikes for reliable, maintenance-free operation.
Fully Automatic Operation
Designed for fully automatic operation, the MWH Series turns on when the motor starter has turned off. A built-in one minute timer ensures that the motor magnetic field has collapsed before it injects DC power into the windings. When the motor is restarted, the MWH Series instantly turns off. No operator interface is required... the MWH Series is in control.
Built-in Overload Sensing
The MWH Series had an optional shutdown input that can be connected to the N.O. auxiliary contact on the motor starter’s thermal overload relay. This will disable the motor winding heater control, preventing any additional heating in the motor and allowing for a faster motor cool down period. The MWH Series then goes back on-line after the overload relay is reset.
Ideal Alternative to Strip Heaters
Eliminate the cost and hassle of installing strip heaters into your motors. Simply wire up the MWH Series to generate heat throughout the motor stator windings. The heat is dissipated evenly without the “hot spots” caused by strip heaters. Conduction of heat to the rotor, bearings and shaft is also more effective which means maximized protection for the whole motor.
.jpg)